Show Menu

Case Studies

Our recent work

When it comes to hydraulic design, manufacture, precision and reliability matter. At Bell Hydraulics we are committed to delivering solutions that drive your success. Here are a few examples of projects that we have been involved with from design concept to full installation.

Filter:

All
Aerospace
Skydrol
Defence
Oil & Gas
Recycling
Aluminium Extrusion
Aerospace

Containerised Hydraulic Power Unit to supply the required pressure and flow to a Servo Test Rig

Fluid: Aeroshell 41

30kW Pump / motor set (65 lpm / 210 bar)

All filtration Hydac

Aerospace

Hydraulic Power Unit to connect to a ring-main in a new facility

Fluid: Castrol Anvol SWX46

132kW pump / motor set

All filtration Hydac

Aerospace

Hydraulic Power Units connected to a ring-main for a new facility

Fluid: Skydrol LD-4.

2 x 90 kW electric motors

220 lpm at 420 bar Hydraulic flow capacity

Skydrol

Hydraulic Test Rig to perform a ‘proof’ pressure & compensator decay test

Fluid: Skydrol LD-4.

11kW Pump / motor set (8 lpm / 540 bar)

All filtration Hydac

Skydrol

Hydraulic Test Rig to perform a ‘proof’ pressure & compensator decay test 2

Fluid: Skydrol LD-4

1.5kW Pump / motor set (1.5 lpm / 345 bar)

All filtration Hydac

Skydrol

Hydraulic Test Rig to supply flow & pressure requirements to test an aircraft Wing Tip Brake

Fluid: Skydrol LD-4.

4kW Pump / motor set (4.5 lpm / 350 bar)

All filtration Hydac

Skydrol

Hydraulic Test Rig to test C-Series TRAS Component Valves

Fluid: Skydrol LD-4

11kW Pump / motor set (28 lpm / 220 bar)

All filtration Hydac

Defence

Hydraulic Power Unit to facilitate a 4.5” bullet pull fatigue Test Rig

Fluid: Mineral Oil (ISO32)

5.5kW pump / motor set (46 lpm / 60 bar)

Pressure relief valve (vented, soft-shift, 24VDC)

Defence

Hydraulic Power Unit to open & close 2 lead lined X-Ray doors

Fluid: Mineral Oil (ISO32)

15kW pump / motor set

1 x Immersion heater (1 kW 415V/3ph/50Hz)

Defence

Hydraulic Test Rig to perform a Production Acceptance Test for a Overspeed Governor Unit

Fluid: Turbo Oil 2380

Working temperature 80°C (all seals Viton)

Variable speed drive c/w close loop feed back

Defence

Hydraulic Test Rig to performing a Production Acceptance Test for a Pitch Control Unit

Fluid: Turbo Oil 2380

1 x 5.5kW Pump / motor set (14 lpm / 210 bar)

Off-line scavenge / filtering system

Defence

Replacement Hydraulic Power Unit for a BIP Horizontal Press

Fluid: Mineral Oil (ISO32)

15kW pump / motor set (116 lpm / 70 bar)

Off-line filtering / cooling loop (27 lpm / 10 micron)

Oil & Gas

Complete overhaul and upgrade of Jetty Cranes

Fluid: Mineral Oil (ISO 32)

30kW Hydraulic Power Unit (ATEX)

Hydraulic pipe work (S/Steel 316L)

Oil & Gas

Complete overhaul and upgrade of Loading Arm Hydraulic Power Units

Fluid: Mineral Oil (ISO 32)

5.5kW Hydraulic Power Unit (ATEX)

Hydraulic pipe work (S/Steel 316L)

Oil & Gas

Manifold assemblies for RB211 Albro Starter Pack

Fluid: Turbine oil

Pressure ramp up & down

Hydac Manifold mounted pressure filters (5 micron)

Recycling

Filter Press Hydraulic Power Unit for the Recycling Industry

Fluid: Mineral Oil (ISO 32)

4kW pump / motor set

420 bar rated

Recycling

Harris Bailer Hydraulic upgrade in the recycling sector

Fluid: Mineral Oil (ISO 46)

1 x 75 kW electric motors

Double vane pump (225 lpm & 225 lpm)

Recycling

Hydraulic Power Unit for scrap yard bailing machining

Fluid: Mineral Oil (ISO46)

90kW Pump / motor set

Air blast cooler

Recycling

Lubrication hydraulic power units for the recycling sector

Fluid: Mineral Oil

0.55kW pump / motor set (1.5 lpm)

Immersion heater

Aluminium Extrusion

Complete hydraulic system on a 2500T aluminum extrusion press

Proportional pressure control

Proportional pre-fill valve

Project manage pipework installation

Aluminium Extrusion

Complete hydraulic system on a 2500T aluminium extrusion press

Accumulator / Auxiliary Block

Pump Loading Block

Main Ram / Side Ram Block

Open quotation marks

We partnered with Bell Hydraulics for a complex engineering project, and we couldn’t be happier with the results. They not only met our expectations but exceeded them, finishing the project on time and within budget.

James Kelly

Managing Director, Kelly Control Systems Ltd

We’re proud to be trusted by

Moog Logo
BP Logo
GE Aviation Logo
Dowty Logo
Dow Corning Logo
MDS Logo
BAE Systems Logo